Are you tired of constantly repairing your old toilet? Or maybe you simply want to upgrade to a more modern and efficient model? Either way, a toilet replacement and installation can be a straightforward and rewarding home improvement project. Whether you are a seasoned DIY enthusiast or a novice in the world of home repairs, this step-by-step guide will walk you through the entire process, ensuring a successful and leak-free installation.
Removing an old toilet
The first step in this project is to remove the old toilet. This can be a messy task, so be prepared with gloves and old towels. Start by shutting off the water supply valve located behind the toilet and flushing it to drain any remaining water in the tank and bowl. Next, unscrew the nuts securing the toilet bowl to the floor and carefully lift the toilet off the flange. Be cautious, as it can be heavy!
Pro tip: Have a trusted friend or family member assist you in lifting the toilet to avoid any accidents.
Installing the new toilet
Once the old toilet is removed, it’s time to install the new one. Begin by placing a new wax ring or gasket on the flange. Make sure it is centered and will create a watertight seal. Then, carefully lower the toilet bowl onto the flange, aligning the mounting bolts with the holes on the toilet base. Gently press down to compress the wax ring and create a secure connection.
Attaching the tank and seat
With the toilet bowl in place, it’s time to attach the tank. Follow the manufacturer’s instructions to secure the tank to the bowl using the included hardware. Be sure to tighten all connections to prevent any leaks. Finally, attach the toilet seat according to the instructions provided. Now, you can turn on the water supply valve and test your newly installed toilet for any leaks or issues.
Remember, if you are unsure about any step of the process, it’s always best to consult a professional plumber. They can ensure that your toilet installation is done correctly and to code, providing you with peace of mind and a fully functional bathroom fixture.
By following this complete toilet removal and installation guide, you can successfully replace and upgrade your toilet, saving money on repairs and enjoying the benefits of a more efficient and modern fixture. So, roll up your sleeves and get ready to tackle this rewarding home improvement project!
Assessing the Need for Toilet Upgrade
Before jumping into the replacement or installation process, it is important to assess if a toilet upgrade is really necessary. Several factors can help determine if it’s time to consider upgrading your toilet:
1. Constant Repairs: If your toilet requires frequent repairs and the cost of maintaining it is becoming a burden, it might be a sign that an upgrade is needed. Upgrading to a newer model can often save you money in the long run.
2. Outdated Design: If your current toilet is outdated and doesn’t match the aesthetics of your bathroom, it could be a good time for an upgrade. Installing a new and modern toilet can improve the overall look and feel of your bathroom.
3. Water Efficiency: Older toilets tend to use more water per flush, leading to higher water bills. Upgrading to a water-efficient toilet can help you save money on your monthly utility bills while also being environmentally friendly.
4. Cracks or Leaks: If you notice any cracks or leaks in your toilet, it’s essential to address them promptly. Constant leaks can result in water damage and mold growth, causing further issues. In such cases, replacing the toilet is often the best solution.
5. Difficulty Flushing: If your toilet has trouble flushing or doesn’t flush efficiently, it may be time for an upgrade. Modern toilets often come with improved flushing mechanisms that ensure better performance and functionality.
Assessing the need for a toilet upgrade can help you make an informed decision about whether it’s time to invest in a new toilet. Considering factors such as repair frequency, design, water efficiency, cracks or leaks, and flushing issues can guide you towards making the right choice for your bathroom.
Selecting a New Toilet
When it comes to bathroom renovation and upgrade, selecting the right toilet is an important decision. Whether you are looking for a replacement or installing a toilet in a new bathroom, considering the right factors can help you make the best choice.
Firstly, you should decide on the type of toilet you need. The most common types include two-piece toilets, which have a separate tank and bowl, and one-piece toilets, which have a combined tank and bowl. Two-piece toilets are generally more affordable and easier to repair, while one-piece toilets are sleeker in appearance and easier to clean.
Next, you should consider the flushing mechanism of the toilet. The two most popular types are gravity-assisted and pressure-assisted. Gravity-assisted toilets use the natural force of gravity to flush the waste, while pressure-assisted toilets use compressed air to create a more powerful flush. Depending on your plumbing system and personal preference, you can choose the flushing mechanism that suits your needs.
It is also important to consider the dimensions and rough-in of the toilet. Measure the space in your bathroom to ensure that the toilet will fit properly. Additionally, check the rough-in distance, which is the distance between the wall and the center of the toilet flange. Most toilets have a rough-in of 12 inches, but it can vary. Make sure you select a toilet with the appropriate rough-in for your bathroom.
Lastly, consider the style and design of the toilet. There are numerous options available, from traditional to modern, so you can choose a toilet that matches your overall bathroom aesthetic. Additionally, consider features such as water-saving technology, ease of cleaning, and comfort options like a soft-close seat.
By considering these factors when selecting a new toilet, you can ensure that your installation or replacement process goes smoothly and that you end up with a toilet that suits your needs and preferences.
Preparing for Toilet Removal
In order to successfully complete a toilet removal and replacement or repair, it is important to properly prepare the area and gather the necessary tools and materials. Here are some steps to follow:
1. Turn off the water supply: Before starting the installation or removal process, it is important to turn off the water supply to the toilet. Locate the shut-off valve, which is usually located on the wall or floor near the base of the toilet, and turn it clockwise until it is fully closed.
2. Flush the toilet: After turning off the water supply, flush the toilet to drain the remaining water in the tank and bowl. This will help minimize any potential mess during the removal process.
3. Remove the water: Use a sponge, towel, or a wet/dry vacuum to remove any remaining water from the tank and bowl. This will make the toilet lighter and easier to handle during the removal process.
4. Disconnect the water supply line: Use an adjustable wrench or pliers to loosen and remove the nut that connects the water supply line to the bottom of the toilet tank. Be prepared for some water to come out when removing the nut.
5. Disconnect the tank from the bowl: Depending on the type of toilet, there may be bolts or nuts holding the tank to the bowl. Use a wrench or pliers to unscrew and remove these connections, then carefully lift the tank off of the bowl.
6. Disconnect the bowl from the floor: There will be two or four bolts securing the toilet bowl to the floor. Use a wrench or pliers to unscrew and remove these bolts, then lift the toilet bowl off the floor. It is a good idea to have some help with this step, as the toilet can be heavy.
7. Prepare the area: Once the old toilet is removed, inspect the flange and floor for any damage. Clean the area thoroughly and make any necessary repairs before proceeding with the installation of the new toilet.
By following these steps and properly preparing for the toilet removal, you can ensure a smoother and more successful installation or replacement process.
Water Shut-Off and Drain Emptying
Before you begin the toilet upgrade installation, it is crucial to shut off the water supply and empty the drain. This step ensures a safe and clean removal of the old toilet and allows for proper repair and installation of the new one.
Shutting off the Water Supply
The first step in the process is to locate the water shut-off valve behind the toilet. It is usually located on the wall or floor near the toilet. Once you have located it, turn the valve clockwise to shut off the water supply. This will prevent any water from flowing into the toilet tank during the removal process.
Drain Emptying
After shutting off the water supply, it is important to empty the toilet drain. To do this, you can use a plunger to push any remaining water and waste down the drain. Alternatively, you can use a shop vacuum to suck out the water from the bowl and tank. Make sure to remove as much water as possible to minimize any mess during the removal and installation process.
Once the drain is empty, you can proceed with the toilet removal and installation without any water leakage or mess. Remember to follow the manufacturer’s instructions for removing and installing the toilet to ensure a proper and secure fit.
Disconnecting the Water Supply
Before you can proceed with the replacement, removal, or installation of a toilet, it is important to disconnect the water supply. Disconnecting the water supply ensures that you can work on the toilet without any water leakage or damage.
To disconnect the water supply to the toilet, follow these steps:
Step 1: Locate the water shut-off valve
The water shut-off valve is typically located behind the toilet, near the wall. It is usually a round or oval-shaped valve with a lever or handle.
Step 2: Turn off the water supply
Turn the handle or lever of the shut-off valve clockwise to shut off the water supply. This will stop the flow of water to the toilet.
Once the water supply is turned off, flush the toilet to drain any remaining water in the tank and bowl. This will prevent any water from spilling when you disconnect the water supply line.
Now that the water supply is disconnected, you can proceed with the removal, installation, or upgrade of the toilet.
Removing the Old Toilet
If you’re considering an installation or replacement of your toilet, the first step is removing the old one. The removal process is straightforward and can be done with basic tools and a little bit of time.
Here are the steps to remove the old toilet:
- Turn off the water supply: Locate the shut-off valve behind the toilet and turn it clockwise to shut off the water supply. Flush the toilet to remove as much water as possible from the tank and bowl.
- Disconnect the water supply line: Using an adjustable wrench, loosen the nut that connects the water supply line to the bottom of the tank. Once the nut is loose, twist it off by hand.
- Remove the tank: Start by removing the tank lid and set it aside. Next, use a wrench to loosen and remove the bolts that secure the tank to the bowl. Once the bolts are removed, carefully lift the tank off the bowl and set it aside.
- Remove the bowl: Locate the bolts at the base of the toilet bowl and remove the nuts with a wrench. Once the nuts are removed, gently rock the bowl from side to side to break the seal with the wax ring. Lift the bowl straight up and carefully move it to a designated area.
- Remove the wax ring: Scrape away the old wax ring from the flange, which is the round opening in the floor. Make sure to clean the flange thoroughly to prepare it for the new toilet installation.
Once you have successfully removed the old toilet, you will be ready to proceed with the installation or replacement of your new toilet. This is a great opportunity to upgrade your toilet to a more efficient and modern model that can help save water and improve your bathroom’s functionality.
Inspecting and Preparing the Flange
Before starting the removal, replacement, or installation of a new toilet, it is important to inspect and prepare the flange. The flange is a circular pipe fitting that connects the toilet to the waste pipe and secures it in place. This step is essential to ensure a proper and leak-free connection.
Begin the inspection by checking the condition of the flange. Look for any cracks, breaks, or signs of damage. If you notice any issues, it is recommended to replace the flange before proceeding. A damaged flange can lead to leaks and instability in the toilet.
If the flange is in good condition, clean it thoroughly to remove any dirt or debris. Use a rag or brush to scrub the flange and ensure that it is free from any grime or residue. A clean flange is necessary for a tight and secure connection with the toilet.
Next, measure the height of the flange to determine if any adjustments are needed. The flange should be level with or slightly above the finished floor surface. If the flange is too low, it may need to be raised using a flange extender or a wax ring with an integrated flange. If the flange is too high, it can be trimmed down using a hacksaw.
Finally, inspect the mounting bolts that secure the flange to the floor. Make sure the bolts are in good condition and properly tightened. If the bolts are rusted or damaged, replace them with new ones. Tighten the bolts securely to ensure the flange is securely attached to the floor.
By inspecting and preparing the flange, you can ensure a smooth and successful toilet removal, replacement, installation, or upgrade project. Taking the time to properly inspect and prepare the flange will help prevent any future issues and ensure a reliable and long-lasting toilet connection.
Installing the New Toilet
Once you have completed the toilet removal and repair or replacement, it’s time to install the new toilet. Follow these steps to ensure a proper installation:
- Begin by placing a wax ring onto the flange opening. Make sure it is centered and level.
- Lower the new toilet bowl onto the wax ring, aligning the bolt holes with the mounting bolts on the flange. Apply gentle pressure to compress the wax ring and create a seal.
- Secure the toilet bowl to the flange by tightening the nuts onto the mounting bolts. Be careful not to overtighten, as this could crack the toilet bowl.
- Next, attach the tank to the toilet bowl, aligning the bolts and tightening the nuts to secure it in place.
- Connect the water supply line to the fill valve on the bottom of the tank. Tighten it securely to prevent leaks.
- Turn on the water supply and fill the tank with water. Check for any leaks around the base of the toilet and ensure proper flushing and refilling.
- If everything is functioning correctly, use a wrench to tighten the nuts on the flange bolts, securing the toilet to the floor. Be careful not to overtighten and crack the toilet.
Once the new toilet is securely installed and functioning properly, you can clean up any remaining debris and enjoy your newly replaced or repaired toilet.
Connecting the Water Supply
Once you have completed the toilet removal and have upgraded or replaced the old unit with a new one, it’s time to connect the water supply. This step is essential for ensuring that your toilet functions properly and is ready for use.
1. Gather the necessary materials
Before you begin, make sure you have all the materials you need. This includes a flexible water supply line, an adjustable wrench, plumber’s tape, and a bucket or towel to catch any water that may leak during the process.
2. Turn off the water supply
Locate the shut-off valve, which is typically located on the wall behind the toilet. Turn the valve clockwise to shut off the water supply. This will prevent any water from flowing into the toilet while you work.
Note: If you cannot find the shut-off valve or it is not working properly, you may need to shut off the main water supply to your home before proceeding.
3. Connect the water supply line
Take one end of the flexible water supply line and attach it to the bottom of the toilet tank. Use an adjustable wrench to tighten the connection, but be careful not to overtighten and cause any damage.
Next, take the other end of the water supply line and attach it to the shut-off valve. Again, use the adjustable wrench to secure the connection. Apply plumber’s tape to the threads of both connections to ensure a tight seal and prevent any leaks.
4. Turn on the water supply
With the water supply line properly connected, slowly turn the shut-off valve counterclockwise to turn on the water supply. Keep an eye out for any leaks and tighten the connections if necessary.
Tip: It’s a good idea to check for leaks by flushing the toilet and inspecting all connections. If you notice any leaks, tighten the connections or consult a professional plumber.
Once you have confirmed that there are no leaks and the water supply is fully connected, your toilet is ready for use. Congratulations on completing the installation process!
Testing for Leaks
After the replacement or repair of a toilet, it is crucial to test for leaks to ensure that the installation was successful. Even the smallest leak can lead to significant water damage over time, so thorough testing is essential.
Follow these steps to properly test your toilet for leaks:
-
Prepare the Testing Area
- Place newspaper or towels around the base of the toilet to quickly identify any water leakage.
- Ensure that the water supply line is fully turned on.
-
Check for Visible Leaks
- Inspect the base of the toilet, as well as the connections between the tank and the bowl, for any signs of water leakage.
- Pay close attention to the wax ring seal underneath the base. If it looks damaged or misaligned, there may be a leak.
- Also, check the water supply line and the connection to the fill valve for any visible leaks.
-
Perform a Dye Test
- Add a few drops of food coloring or a dye tablet to the toilet tank.
- Wait for about 15-20 minutes without flushing the toilet.
- If any colored water appears in the toilet bowl, it indicates a leak between the tank and the bowl.
-
Inspect the Flush Valve and Flapper
- Remove the tank lid and flush the toilet.
- Observe the flush valve and flapper to ensure they close properly and form a watertight seal after flushing.
- If the flapper does not seal tightly or the flush valve is defective, it can cause leaks.
By following these steps, you can identify and resolve any leaks in your toilet installation, ensuring efficient water usage and preventing water damage. Always make sure to test for leaks after any toilet upgrade or repair.
Troubleshooting Toilet Installation Issues
Installing a new toilet can be a significant improvement or an essential task that needs to be done. However, sometimes issues may arise during the toilet installation process that may require troubleshooting. In this section, we will discuss common problems that can occur during toilet replacement, removal or upgrade, and provide solutions to resolve them.
1. Leaking Base
One of the most common installation issues is a leaking base. This can happen if the wax ring is not properly aligned or if there are cracks in the toilet base. To fix this problem, you can try repositioning the wax ring or replacing it with a new one. Additionally, inspect the toilet base for any signs of cracks or damage and replace the toilet if necessary.
2. Loose Toilet Seat
If the toilet seat feels loose, it may not have been properly tightened during installation. To fix this, check the bolts securing the seat to the toilet bowl and tighten them. If the bolts are stripped or damaged, replace them with new ones.
Another common issue with the toilet seat is that it shifts or moves when sitting on it. This can happen if the seat is not properly aligned with the toilet bowl. To fix this, make sure the seat is centered and aligned correctly, and then tighten the bolts.
3. Flushing Problems
If the toilet has flushing problems such as weak flushing or water not draining properly, several issues may be causing it. First, check the water level in the tank and adjust the float valve if necessary. The water level should be below the overflow tube but high enough to allow proper flushing.
Secondly, check the flush valve and flush mechanism to ensure they are functioning correctly. Clean or replace any parts that are worn out or damaged. If these steps do not resolve the flushing problems, it may be necessary to call a professional plumber for further inspection.
4. Uneven Toilet
If the toilet is not sitting evenly on the floor, it may rock or wobble when used. This can happen if the toilet is not properly leveled during installation. To fix this, place shims under the base of the toilet to level it. Once the toilet is level, tighten the bolts connecting the toilet to the floor.
If the toilet still rocks or wobbles after leveling, there may be an issue with the flange. Inspect the flange for any damage or cracks and replace it if necessary.
| Issue | Solution |
|---|---|
| Leaking Base | Reposition or replace the wax ring. Check for cracks in the toilet base. |
| Loose Toilet Seat | Tighten the bolts securing the seat. Replace stripped or damaged bolts. |
| Flushing Problems | Check water level, float valve, and flush mechanism. Clean or replace worn-out parts. |
| Uneven Toilet | Level the toilet using shims. Inspect and replace the flange if necessary. |
Toilet Repair: Common Problems and Solutions
When it comes to toilet maintenance, there are a few common problems that can arise. Luckily, many of these issues can be easily fixed without the need for a professional plumber. Here are some of the most common toilet problems and their solutions:
- Clogged Toilet: A clogged toilet is one of the most common problems homeowners face. To fix this issue, you can try using a plunger or a toilet auger to break up the clog. If that doesn’t work, you may need to remove the toilet and manually remove the obstruction.
- Running Toilet: If your toilet constantly runs, it can waste a significant amount of water and increase your water bill. The most common cause of a running toilet is a faulty flapper valve. To fix this, simply replace the flapper valve with a new one.
- Leaking Toilet: A leaking toilet can cause water damage to your bathroom floor and waste water. One common cause of a leaking toilet is a worn-out wax ring. To fix this, you will need to remove the toilet and replace the wax ring. If the leak is coming from the tank, you may need to replace the tank-to-bowl gasket.
- Weak Flush: If your toilet has a weak flush, it may not be powerful enough to effectively remove waste. One possible solution is to adjust the water level in the tank by adjusting the float or fill valve. You can also try cleaning the rim holes and jet holes to ensure proper water flow.
- Toilet Replacement and Upgrade: If your toilet is old or not functioning properly, you may need to consider replacing it. When choosing a new toilet, look for water-efficient models that can help you save on your water bill. The installation process for a new toilet is similar to a repair, but you will need to remove the old toilet and install the new one.
By addressing these common toilet problems and finding the appropriate solutions, you can ensure that your toilet functions properly and avoid costly repairs in the future. Remember, if you’re unsure about any of these repairs or if the problem persists, it’s always best to consult a professional plumber.
DIY Toilet Repair Tips
If you’re experiencing problems with your toilet, it’s always a good idea to try a DIY repair before calling in a professional. Here are some tips to help you with your toilet repair:
1. Troubleshooting Common Toilet Issues
Before you start repairing your toilet, it’s important to identify the problem. Check for leaks, clogs, or any other issues that may be causing your toilet to malfunction.
2. Repairing a Leaky Toilet
If you have a leaking toilet, it’s likely due to a faulty flapper valve or a damaged flush valve. To fix this issue, you’ll need to purchase a replacement flapper or flush valve and install it according to the manufacturer’s instructions.
3. Unclogging a Toilet
If your toilet is clogged, you can try using a plunger to remove the blockage. Place the plunger over the drain hole and apply firm pressure while vigorously plunging up and down. If that doesn’t work, you can try using a toilet auger, which is a long and flexible tool specifically designed for unclogging toilets.
Note: Avoid using chemical drain cleaners as they can damage your toilet and pipes.
4. Replacing a Toilet Seat
If your toilet seat is cracked, broken, or just needs an upgrade, you can easily replace it. Remove the old seat by unscrewing the bolts located under the rim of the toilet bowl. Then, attach the new seat by aligning it with the bolt holes and tightening the bolts.
5. Upgrading Your Toilet
If you’re looking to upgrade your toilet for better water efficiency or a more modern look, consider replacing your old toilet with a new one. There are many options available, including dual-flush toilets and low-flow toilets, which can help you save water and money in the long run.
Note: If you’re not confident in your DIY skills or if the problem persists after attempting the repairs, it’s best to consult a professional plumber to avoid further damage.
| Issue | Possible Causes | DIY Solution |
|---|---|---|
| Leaky toilet | Faulty flapper valve or damaged flush valve | Replace flapper or flush valve |
| Clogged toilet | Blockage in the drain | Use a plunger or toilet auger to remove the blockage |
| Cracked or broken toilet seat | Worn out or damaged seat | Replace with a new toilet seat |
| Outdated or inefficient toilet | Older model with high water consumption | Upgrade to a more water-efficient toilet |
When to Consider Toilet Replacement
While a toilet is a durable fixture in your bathroom, there may come a time when you need to consider replacing it. Here are a few situations when toilet replacement might be necessary:
1. Constant repairs: If you find yourself frequently calling a plumber to fix your toilet, it may be time to consider a replacement. Constant repairs can be a sign of underlying issues that are not easily fixable.
2. Old and outdated: If your toilet is old and outdated, it might be time for an upgrade. Older toilets may not be as efficient in water usage and may not have the latest features like dual-flush technology.
3. Cracks or leaks: Cracks or leaks in the toilet bowl or tank can cause water damage to your bathroom floor and walls. If you notice any cracks or leaks, it’s best to replace the toilet to avoid further damage.
4. Consistent clogging: If your toilet consistently clogs, even after attempts to unclog it, it could be a sign of a larger issue. Upgrading to a toilet with more flushing power may be necessary.
5. Renovations or remodeling: If you’re planning a bathroom renovation or remodeling project, it’s a good opportunity to replace your toilet. A new toilet can add a fresh look to your bathroom and be more in line with your design preferences.
If you’re experiencing any of these situations, it’s worth considering toilet replacement. An upgraded and properly installed toilet can improve your bathroom’s functionality and save you money on future repairs.
Selecting a New Toilet for Replacement
When it comes time to upgrade or replace your toilet, there are a few key factors to consider. The right toilet can not only improve the functionality of your bathroom, but also enhance its aesthetics. Here are some important things to keep in mind when selecting a new toilet:
1. Measurements and Compatibility
Before purchasing a new toilet, you need to ensure that it will fit in the space where your old toilet was. Measure the rough-in, which is the distance from the wall to the center of the toilet flange, to ensure compatibility. Additionally, consider the overall dimensions of the toilet to ensure it will fit within your bathroom layout.
2. Water Efficiency
Water conservation is becoming increasingly important, so it’s worthwhile to opt for a toilet that is water-efficient. Look for toilets that are labeled with the WaterSense certification, as these toilets meet water efficiency and performance standards set by the Environmental Protection Agency (EPA).
Some toilets offer dual-flush options, allowing you to choose between a full flush or a partial flush depending on your needs. This can help further reduce water consumption, saving you money in the long run.
3. Style and Design
The style and design of your toilet can greatly impact the overall look of your bathroom. Consider the aesthetics of your bathroom and choose a toilet style that complements the existing decor. Popular options include traditional, modern, and contemporary designs.
You’ll also want to consider the shape of the toilet bowl. Common options are round and elongated, with elongated bowls offering additional comfort for adults.
Additionally, think about the color or finish of the toilet. Common options are white, beige, and black, but there are also toilets available in a variety of other colors to suit your personal preferences.
4. Price and Budget
As with any home improvement project, it’s important to consider your budget when selecting a new toilet. Toilet prices can vary greatly depending on the brand, features, and materials. Set a budget and compare prices across different options to find a toilet that meets your needs without breaking the bank.
Remember, the goal of selecting a new toilet for replacement is to find a reliable and efficient fixture that will serve your needs for years to come. Take the time to research and compare different options to ensure you are making the best choice for your bathroom’s upgrade, repair, or replacement.
Hiring a Professional for Toilet Removal and Installation
When it comes to upgrading, repairing, or installing a new toilet, it’s always a good idea to hire a professional. While some homeowners may feel confident in tackling this project themselves, there are several reasons why bringing in an expert is the smarter choice.
Experience and Expertise: A professional plumber has the necessary knowledge and expertise to handle toilet removal and installation. They understand the intricacies of plumbing systems and can ensure that the job is done correctly the first time.
Time and Efficiency: Hiring a professional can save you time and effort. They have the necessary tools and equipment to efficiently remove your old toilet and install a new one. They can complete the job in a fraction of the time it would take you to do it yourself.
Quality Workmanship: A professional plumber can provide high-quality workmanship. They have the skills and experience to install your new toilet in a way that ensures its proper functioning and longevity. They will also make sure that all connections are secure and leak-free.
Safe and Secure: A professional plumber will prioritize safety throughout the removal and installation process. They know how to handle heavy toilets without causing damage to your floors or walls. They will also take proper precautions to prevent any accidents or injuries.
Warranty and Guarantee: Many professional plumbers offer warranties or guarantees on their work. This provides you with peace of mind knowing that if any issues arise after the installation, they will come back and fix them at no additional cost to you.
Overall, hiring a professional for toilet removal and installation is a smart decision. They have the necessary experience, tools, and skills to complete the job efficiently and to a high standard of quality. By entrusting the task to a professional, you can enjoy a stress-free installation process and a properly functioning toilet for years to come.